Wiring Specialties RB26DETT Haltech Elite 2500 ECU Wiring Harness for R32 Skyline GTR - PRO SERIES
$1,291.05
Wiring Specialties RB26DETT Haltech Elite 2500 ECU Wiring Harness for R32 Skyline GTR - PRO SERIES
PRO Series Plug-n-Play for R32 GT-R AWD
Configured for the Haltech Elite 2500 Aftermarket ECU
This Wiring Specialties PRO Series harness was designed from the ground-up to exceed OEM specifications for wire quality, power/ground routing. With our optimized and 'tucked' approach the end result will be a clean and worry free installation with a guaranteed start up.
This harness is specifically engineered for a JDM RHD AWD Nissan Skyline R32 GT-R with the RB26DETT engine & AWD Transmission using the Haltech Elite 2500 Aftermarket ECU. It was developed in house on an actual RB26DETT engine to ensure a perfect fit to all engine connections.
Wiring Specialties offers a number of options for common performance upgrades for this product. Build your perfect harness by selecting from the available options to the right, and as always - if you have any questions, please reach out to us.
ENGINE: R32 Skyline GTR RB26DETT
- Any RB26DETT from 1989-1994 Skyline R32 GTR
CHASSIS: Skyline R32 GT-R AWD
- Any R32 Skyline GT-R AWD manufactured in 1989-1994 (Including ABS cars)
- Factory Speedometer, Tachometer, Alternator Warning light, Oil Pressure Gauge, AC, wipers and reverse lights remain functional.
- For accurate coolant gauge functionality, the R32 OEM 1-pin coolant temp switch should be used in the RB26 coolant elbow.
PRO-SERIES HARNESS TECHNICAL SPECS
- Plug and Play – simple and efficient
- NO CORE HARNESS or additional wiring required
- OEM wire colors used, where applicable
- All sensor signal connections use EM shielded wires
- Fireproof fiberglass sleeving used in high-temp sections near the manifold & turbo (-40°C/-40°F to +450°C/+845°F operating temperature)
- Point-to-Point continuity tested on every wire
- Constructed using exact OEM connectors and seals
- Made with high temp TXL wire with adhesive shrink tubing (-40°C/-40°F to +125°C/+257°F operating temperature)
- Wrapped in lightweight nylon loom (-94°C/-137°F to +125°C/+257°F operating temperature)
- Includes a charge harness and improved grounds
- Fully tested after production for an easy plug-and-play installation
PRO-SERIES HARNESS INCLUDES
- Main Engine and Transmission one-piece tucked harness
- Alternator charge cable
- 6x Coilpack connections
- 6x Injector connections
- 2x Knock sensor connectors
- 2x MAFS connectors
- TPS connector
- TPS switch connector
- Boost solenoid wiring
- 5-pin and 6-pin igniter chip connectors, unless upgrading to Smart Coils
- Cam sensor connector
- Idle air solenoid connector
- 2x Aftermarket WB Oxygen sensor connectors
- 2x ground ring terminals
- Air regulator connector (under intake manifold location)
- ECT sensor connector and cluster coolant temp switch connector
- Reverse lights sensor connector
- Speed sensor connector
- Alternator connector
- Starter signal connector
- Oil pressure connector
- Nissan ECU Diagnostics mode connector
- Dash and fuse box connections through the Interface harness
- Printable install instructions with pictures
- Turn Key ENGINE START Guarantee
- Tech support for our customers 7 days a week
AFTERMARKET ECU DETAILS
- Wire-In Aftermarket ECU build harnesses are pre-wired for Oil Pressure, Fuel pressure, Oil Temp, IAT and MAP sensor wiring directly to the ECU.
- Flex Fuel support is available - please contact Sales.
- ECU control of a Boost Control Solenoid wiring is also included.