Wiring Specialties 2JZGTE / 2JZGE VVTi Wiring Harness for USDM Supra JZA80 - PRO SERIES

Looking for a Plug and Play solution for your Supra?  Our Pro Series Harness is our solution for saving you time and headache.  This harness includes full CANbus integration so you can forget about those electrical gremlins once and for all.  

This harness is perfect for a USDM MKIV Supra (1993-1998) with the Turbo 2JZGTE VVTi or Non-Turbo 2JZGE VVTi engine.  This harness was developed in house on an actual 2JZ VVTi engine to ensure a perfect fit to all engine connections.

• Plug and play installation into the chassis using a completely new Wiring Specialties PRO harness (no cutting or modifying factory wiring)
• Gauge functionality with tach, coolant  temp, CEL, Speedometer - fully functional
• Supported A/C functionality with stock Toyota lines and pressure sensor
• Supports proper Power Steering operation (variable if ABS controller is retained)
• Supports aftermarket ECU's only

ENGINE: JZS161 & JZA80 2JZGTE VVTi Turbo; also JCE10, JZZ31 & JZS160 2JZGE VVTi Non-Turbo Engines

• Any VVTI 2JZGTE from JDM Aristo model years 1997-2002
  
• Any VVTI 2JZGTE from JDM Supra RZ model years 1997-2002
• Any VVTI 2JZGE from JDM Soarer JZZ31 model years 1997-2000
• Any VVTI 2JZGE from JDM Aristo JZS160 model years 1997-2004
• Any VVTI 2JZGE from USDM SC300 JZZ31 model years 1998-2001
• Any VVTI 2JZGE from USDM IS300 JCE10 model years 2001-2005
• Any VVTI 2JZGE from USDM GS300 JZS160 model years 1998-2005
• Oval Alternator, New Style Starter, and Plastic Coolant & Oil pressure connector supplied by default. If you need different connectors for these please leave a Note / Comment when checking out.
• Standard – VVTi batched ignition (chip and coils) are supplied, but sequential NON VVTi ignition is available as an option.
• For GM/LQ9 coils – upgrade should be used with an aftermarket ECU and run sequentially. OEM ECUs require IGF signal produced by the ignition chip. When the chip is removed for LQ9 coil installation, an aftermarket ECU or IGF simulator box is required.

CHASSIS: USDM MKIV Supra (1993-1998)

PRO-SERIES HARNESS TECHNICAL SPECS

• Plug and Play – simple and efficient
• NO CORE HARNESS or additional wiring required
• OEM wire colors used, where applicable
• All sensor signal connection use EM shielded wires
• Super-High Temp Fireproof fiberglass loom used on knock sensor, O2 sensor & transmission branches located in hot areas. (-40°C/-40°F to +450°C/+845°F operating temperature)
• Point-to-Point continuity tested on every wire
• Constructed using exact OEM connectors and seals
• Made with high temp TXL wire with adhesive shrink tubing (-40°C/-40°F to +125°C/+257°F operating temperature)
• Wrapped in lightweight nylon loom (-94°C/-137°F to +125°C/+257°F operating temperature)
• Includes a charge harness and improved grounds
• Fully tested after production for an easy plug-and-play installation

FAQ & OTHER DETAILS

• Alternator Charge Cable - This item ties the starter/battery directly to the Alternator output, which allows the improved power routing on our harness to eliminate the wire running from the alternator to the fusebox and/or battery while still charging the battery normally.
• Grounding Kit - Our Kit ties a number if engine components to the body of the car and ensures that you will not have issues resulting from poor grounds. The Grounding Kit utilizes Ultra High temp fiberglass sleeving to allow installation under or around exhaust components. Very flexible mounting options allow you to connect the block, head, battery tray, alternator case and chassis to completely eliminate all grounding issues.
• Speedo Signal Conditioning - The Dakota Digital SGI-5 unit for Speed can 'condition' the signal to compensate for cross-platform swaps. If the Option exists to ADD the unit on the harness page for your swap, then you need it for proper speedo operation. Please note that some transmissions (350z, BMW ZF and S15 Silvia for example) do not have a speed sensor and will require a non-harness based solution like a GPS speedo.
• Plug-n-Play vs Universal - Plug-n-Play harnesses connect to your car's underhood fuse box for power and to connectors under the dash for gauges etc. Universal harnesses do not need an underhood fusebox to connect to and the wiring for gauges and warning lights is provided as a 'flying lead' which are bare wires labeled with their function.
• Right Hand Drive (RHD) Conversions - If you used ALL the stock LHD chassis connectors for your RHD swap, order the LHD version of the harness. If you used ALL the clip/swap RHD chassis connectors, order the RHD version of the harness. If you used a combination of LHD and RHD chassis connectors, please contact us as our harnesses will need modification.
• Don't See It? - If you have injectors, throttle body, coilpacks or any other item that you do not see on the Options offerings, please contact us. Chances are we can do it!
• Battery Cables / Battery Relocation - The battery must be connected to the starter, so you need a battery cable from the positive battery terminal to the starter main power lug. Typically this positive battery cable also powers up the main under hood fusebox, which runs many of the non-engine items on your car like interior lights, dash power and headlights/taillights. Please make sure you have prepared for this as each install is different.