Wiring Specialties 2JZGTE VVTI Pro Series Wiring Harness for Nissan Skyline GTS R32
$1,075.00
Looking for the best in aesthetics, weight savings and reliability out of your harness? Our Pro Series harness completely replaces your old OEM harness so you can forget about those electrical gremlins.
This Wiring Specialties PRO Series harness was designed from the ground-up to exceed OEM specifications for wire quality, power/ground routing. With our optimized and 'tucked' approach the end result will be a clean and worry free installation with a guaranteed start up.
This harness is specifically engineered for a JDM RHD Nissan Skyline R32 GTS/GTS-T/GTS-4 with the 2JZGTE VVTi engine swap. It was developed in house on an actual 2JZGTE VVTi engine in an R32 chassis to ensure a perfect fit to all engine connections.
Wiring Specialties offers a number of options for common performance upgrades for this product. Build your perfect harness by selecting from the available options to the right, and as always - if you have any questions, please reach out to us.
ENGINE: JZS161 and JZA80 2JZGTE VVTi
- Any VVTI 2JZGTE from JDM Aristo model years 1997-2002
- Any VVTI 2JZGTE from JDM Supra RZ model years 1997-2002
- Oval Alternator, New Style Starter, and Plastic Coolant & Oil pressure connector supplied by default. If you need different connectors for these please leave a Note / Comment when checking out.
- Standard – VVTi batched ignition (chip and coils) are supplied, but sequential NON VVTi ignition is available as an option.
- For GM/LQ9 coils – upgrade should be used with an aftermarket ECU and run sequentially. OEM ECUs require IGF signal produced by the ignition chip. When the chip is removed for LQ9 coil installation, an aftermarket ECU or IGF simulator box is required.
CHASSIS: Skyline R32 GTS/GTS-T/GTS-4
- Any R32 GTS Skyline manufactured in 1989-1994 (Including RWD and ABS cars)
- For proper Speedometer functionality, the SGI-5 speed signal calibrator must be used.
- For accurate coolant gauge functionality, the R32 OEM 1-pin coolant temp switch should be used in the JZ’s coolant elbow.
- Retains functional Tachometer, oil pressure display, alternator charge light, reverse lights and wipers.
- A/C wiring utilizes stock R32 fuse box AC relay and wiring. The JZ AC compressor connector must be wired to the chassis’ output AC signal wire.
PRO-SERIES HARNESS TECHNICAL SPECS
- Plug and Play – simple and efficient
- NO CORE HARNESS or additional wiring required
- OEM wire colors used, where applicable
- All sensor signal connection use EM shielded wires
- Fireproof fiberglass sleeving used in high-temp sections near the manifold & turbo (-40°C/-40°F to +450°C/+845°F operating temperature)
- Point-to-Point continuity tested on every wire
- Constructed using exact OEM connectors and seals
- Made with high temp TXL wire with adhesive shrink tubing (-40°C/-40°F to +125°C/+257°F operating temperature)
- Wrapped in lightweight nylon loom (-94°C/-137°F to +125°C/+257°F operating temperature)
- Includes a charge harness and improved grounds
- Fully tested after production for an easy plug-and-play installation
PRO-SERIES HARNESS INCLUDES
- Main Engine and Transmission one-piece tucked harness
- 3x Coilpack connections
- 2x Knock sensor connectors
- MAP connector
- IAT connector
- TPS connector
- Boost solenoid wiring (with AEM/Haltech or aftermarket computers)
- VVT-I connector
- 10-pin igniter chip connector (relocated to inside the car)
- 2x CAM sensor connector
- Crank sensor connector
- Idle air motor connector
- OEM Oxygen sensor connectors (wideband wiring is not part of the EFI harness, except AEM Infinity 6/8)
- 2 x Ground ring terminal
- ECT sensor connector and cluster coolant temp switch connector
- Reverse lights sensor connector
- Speed sensor connector
- Alternator connector
- Starter signal connector
- OEM oil pressure 1-pin connector
- Speed and Tach signal converter connector
- ECU Diagnostics mode connector
- ** No traction Control wiring supplied
- Printable install instructions with pictures
- Turn Key ENGINE START Guarantee
- Tech support for our customers 7 days a week
AFTERMARKET ECU DETAILS
- If you are running an aftermarket ECU, we can customize your PRO harness to fit your exact build requirements. Submit the ECU / Build details form with your order, or we will contact you once the order is placed to collect the needed details.
- AEM Infinity, Link and ECU Masters products (and some other standalone ECUs) are able to process a wideband signal input wired DIRECTLY to the ECU. The LSU 4.2 Version of the WB O2 Sensor SHOULD be used, as per AEM and ECU Masters. Select the Oval or Rectangular connector style in the options to match your WB O2 connector.
- All ECUs that are unable to process a wideband signal directly, will be wired for a FACTORY O2 sensor and a labeled flying lead will be provided to connect the ECU to the Wideband controller. For ECUs that do not process a raw wideband signal, a controller must be used. Controllers like an AEM UEGO Gauge Kit or the Haltech CAN wideband unit should be used.
- AEM Infinity, Motec, Link and ECU Masters harnesses are pre-wired for Oil Pressure, Fuel pressure, Oil Temp, IAT and MAP sensor wiring directly to the ECU. Flex Fuel support is available if desired. ECU control of a Boost Control Solenoid is also available on most harnesses.
- Apex’i PFC conversions ONLY include the IAT sensor in the main harness. The MAP sensor is wired separately, from the PFC box directly to the sensor. MAP sensor harness should be purchased with the PFC.
Legal only for use in competition vehicles which may never be registered, licensed, and/or used on public streets or highways; and also for use in other exempted vehicles.